It is best do a Dyno run before and after to see any given results.
----------------------------------
Steven St.Laurent
Test Engineer
Test Branch, GSD, MCTSSA
MARCORSYSCOM, USMC
Tel: (760) 725-2296
stlaurents@mctssa.usmc.mil
mailto:Saint1958@home.com
-----Original Message-----
From: Morrison, Dennis [mailto:DMorriso@ciena.com]
Sent: Thursday, April 13, 2000 11:29 AM
To: 'dakota-truck@buffnet.net'
Subject: RE: DML: NEED HELP PLEASE!
I THOUGHT ABOUT THE RAM-AIR STYLE DOWN TO THE FENDER (sorry about caps). I
think I am going to look into a home-brew, remove the plastic piece in the
front and replace it with good, quality screen. I will keep all posted.
-----Original Message-----
From: Stlaurent Mr Steven [mailto:STLAURENTS@mctssa.usmc.mil]
Sent: Thursday, April 13, 2000 2:17 PM
To: 'dakota-truck@buffnet.net'
Subject: RE: DML: NEED HELP PLEASE!
What about RAM AIR version? Either through a hood and air hat or tube to
the front fender.
----------------------------------
Steven St.Laurent
Test Engineer
Test Branch, GSD, MCTSSA
MARCORSYSCOM, USMC
Tel: (760) 725-2296
stlaurents@mctssa.usmc.mil
mailto:Saint1958@home.com
-----Original Message-----
From: Bernd D. Ratsch [mailto:bernd@texas.net]
Sent: Thursday, April 13, 2000 10:03 AM
To: dakota-truck@buffnet.net
Subject: RE: DML: NEED HELP PLEASE!
Not really required. I've tested a home-built "QuickD" style and I own a
K&N Gen-II system as well. I noticed no difference with or without the
heat shield.
- Bernd
http://www.toycrusher.com
At 11:41 AM 04/13/2000 -0400, you wrote:
>I went to the site and looked at the pics. Why is there not a heat shield?
>Or is that just for picture sake?
>Awful expensive for a 5hp gain? Will it fit on a V6 with AC?
>
>Sorry about all the questions but you seem so knowledgeable.
>
>TIA
>DENNIS
>
>-----Original Message-----
>From: Bernd D. Ratsch [mailto:bernd@texas.net]
>Sent: Thursday, April 13, 2000 9:31 AM
>To: dakota-truck@buffnet.net
>Subject: RE: DML: NEED HELP PLEASE!
>
>
>
>http://www.quickd.com
>
>Or.....
>
>You can fabricate a "Home Brew" version with simple plumbing parts from
>Home Depot. (Personally, try the QuickD.)
>
>- Bernd
>
>At 08:00 AM 04/13/2000 -0400, you wrote:
> >Thanx Bernd -- but where do I get one for a '99, V6?
> >
> >TIA
> >Dennis
> >
> >-----Original Message-----
> >From: Bernd D. Ratsch [mailto:bernd@texas.net]
> >Sent: Wednesday, April 12, 2000 4:39 PM
> >To: dakota-truck@buffnet.net
> >Subject: Re: DML: NEED HELP PLEASE!
> >
> >
> >
> >Get a QuickD. You'll be much happier with it. Some of us V6'ers have
> >tried the "Chrome Air Cleaner" (if that's what you're referring to) and
> >found that the Intake tube works much better.
> >
> >- Bernd
> >
> >
> >At 03:31 PM 04/12/2000 -0400, you wrote:
> > >Ok I have a '99 SLT+, CC, 4x4, 3.9L V6 with a Flowmaster dual cat-back.
I
> > >am going to get a K&N FIPK, but I do not know where to get one for my
> > >truck -- any suggestions? Also I need to know what cheap mods I can do
to
> > >get this snail moving, but want to keep the cost down. Any help would
be
> > >greatly appreciated.
> > >
> > >TIA,
> > >DENNIS
> > >
This archive was generated by hypermail 2b29 : Fri Jun 20 2003 - 11:50:43 EDT