I don't know if this went out yesterday so I'm sending it again. If it
went out I apologise for the double post.
Kyle
A lot of that stuff I've already done. Thanks for the info on the dual
snorkel setup. I may try it. My other thought was to try to come up with
a setup similar to NASCAR. Taking in air from the base of
the windshield and using the stock hood.
I like the exhaust most of the time. Some times around the mid 2000 rpm
range it gets alittle loud in the cab.
I tried the V8 TB after the cat-back. I was sort of guessing the dreaded
bad sensors problem but I thought I would ask if anyone else tried.
Another question to all. How long should the catalytic convertor last?
Mines original and I'm thinking about getting it changed at the next
inspection in June. It doesn't rattle. Thanks.
Doug
DML Digest wrote:
> > I am relatively new to the list and just wanted to say Hi. I've been
> > reading the list for a couple of months now in digest form. I have to
> > already say thanks to pretty much everyone because you've given me tips
> > and motivation to play more with my truck. I've got a copper metallic 92
> > CC V6, 5 speed, 3.55 sg Dak. I bought the truck new and have 105K on
> > it. I've done the basics sofar. Dynomax cat back exhaust, K&N filter in
> > an Edelbrock housing, and some ignition upgrades. I've got a couple of
> > questions. Has anyone out there tried bolting a V8 TB on their V6? I got
> > a hold of one once and tried it and it felt like I lost to much low end.
> > The '92s had the old fashioned round air cleaners. I've seen the mod
> > with the dual snorkels. Can this setup still flow enough air. I've got
> > the open element filter but would much prefer to have cool air. I know
> > flipping the lid helps alot (I did that until I got the new setup) but
> > that air is still from under the hood. Last question, How many of you
> > are from Upstate NY? I live outside of Rochester near Lake Ontario.
> > Thanks.
>
> Doug,
> Welcome. I am currently running dual cold air ducts, which I have noticed
> some gas mieage increase and good overall performance gains, especially over
> 2000 rpms....like on the highway and such. I did the dual cold air duct mod
> for only about $15, well worth it to me. Cold air anyday is alot better than
> warm engine bay air. I also have QuickD TB on order. I figure a TB will
> finish off my air intake mods, since I have done the following, I figure a
> performance TB is needed to cap off my intake
> mods:
> - -Removed the 'air restrictor plate' at the grill for the factory cold air
> duct
> - -Added an Amsoil 2Stage Hi-Flow Air Filter
> - -Tornado Air Management System, dont laugh.....I got suckered into it about
> 3 years ago, it hasnt done anything help my truck, but I just like to say I
> have one :)
> - -Grafted in a second factory cold air intake duct, using a 4" duct. I bought
> a stock air filter housing(round type from a GenII Dak) and cut out the
> 'neck' and part of the metal round housing which connects the cold air duct
> to the filter housing. The part I cut out just is the area around the
> housing's duct 'neck'. I then cut a hole the size of the neck and slid the
> neck and metal housing over this hole in my filter housing, sealing it up
> with clear silicon and 4 stainless steel screws. I then ran the factory air
> duct(which I also got with the housing I bought) and connected it to a 4"
> duct, which I bought at PepBoys and ran this duct to the grill, right about
> the factory air duct. If you look, there is a second rectangular hole in the
> grill right above the rectangular hole the factory air duct uses. I mounted
> another neck, same as the one on the factory duct, and popped it into the
> hole. Dual cold air intake ducts with an awesome factory look.
> - -I sealed up all connections with clear silicon RTV, so no cold air escapes
>
> How do you like the Dynomax exhaust sound on your V6?
> Kyle
> 93 Dakota 4x4 V6
>
>
This archive was generated by hypermail 2b29 : Fri Jun 20 2003 - 11:50:51 EDT