Ron, just curious, what do you do for a living? After seeing two Vipers in
your driveway and one R/T Dakota but who owns that PT Cruiser stamped
Hennessy Motorsports? Bahahahahaha
-------------------------------------------
Steven St.Laurent
Test Engineer
Test Branch, GSD, MCTSSA
MARCORSYSCOM, USMC
760-725-2506 (DSN 365-2506)
Work:mailto:stlaurents@mctssa.usmc.mil
Home:mailto:saint1958@home.com
-----Original Message-----
From: Ronald Wong [mailto:ron-wong@home.com]
Sent: Friday, September 15, 2000 10:08 AM
To: dakota-truck@buffnet.net
Subject: DML: RE: RE: RE: ignition coils
Oh, that was yours? Too bad....outta sight....outtta mind! ;-P
Ron
00 SLT QC 4X2 5.9 46RE 3.92 LSD
For modifications see my DML Profile
-----Original Message-----
From: owner-dakota-truck@buffnet.net
[mailto:owner-dakota-truck@buffnet.net]On Behalf Of Stlaurent Mr Steven
Sent: Friday, September 15, 2000 8:07 AM
To: 'dakota-truck@buffnet.net'
Subject: DML: RE: RE: ignition coils
Ok! Who stole my ignition coil??? Come on! CONFESS YOU @#$@@;...
hehehehehehehehe
-------------------------------------------
Steven St.Laurent
Test Engineer
Test Branch, GSD, MCTSSA
MARCORSYSCOM, USMC
760-725-2506 (DSN 365-2506)
Work:mailto:stlaurents@mctssa.usmc.mil
Home:mailto:saint1958@home.com
-----Original Message-----
From: Ronald Wong [mailto:ron-wong@home.com]
Sent: Thursday, September 14, 2000 5:40 PM
To: dakota-truck@buffnet.net
Subject: DML: RE: ignition coils
I made them myself. It's really pretty easy. The stock wires to the coil
run along the right valve cover. They're shielded by the black convoluted
tubing. Those wires connect to the stock coil with a special Dodge
connector. I just cut the wires about 6-8 inches before the connector. The
Blaster SS coil from MSD has male disconnects that screw onto the coil. I
took the 6-8 inches hanging from the stock coil and put male disconnects on
them as well. If you're installing the MSD ignition module as well you will
want the small black wire from the MSD module to the black/gray (-) wire of
the coil; you will want the orange wire from the MSD module to the dk
green/orange (+) wire of the coil. Remember the other part of the wire you
cut back at the beginning? One of the wires is black/gray (-), originates
from the distributor; the other is a dk green/orange (+) , originates from
the ignition on your steering column. Again, if you're using the MSD module
you'll connect the black/gray (-) to the white wire of the MSD module;
you'll connect the dk green/orange (+) wire to the small red wire of the MSD
module. If you're not installing an MSD ignition module, you would connect
those two wires to the Blaster coil negative and positive respectively.
Have I totally confused you?
Ron
00 SLT QC 4X2 5.9 46RE 3.92 LSD
For modifications see my DML Profile
-----Original Message-----
From: owner-dakota-truck@buffnet.net
[mailto:owner-dakota-truck@buffnet.net]On Behalf Of jay & dana
Sent: Thursday, September 14, 2000 4:42 PM
To: DML
Subject: DML: ignition coils
Thanx for your response Ron.
A few more questions. Do you know if the blaster coil will fit onto the
stock 1997 harness (my coil is in the same place as yours, your right dumb
place)? Does the MSD come with quick disconnects as you described or did
you install them yourself?
TTYL
Jay
This archive was generated by hypermail 2b29 : Fri Jun 20 2003 - 11:54:35 EDT