i got some pics tonight, i'll send you guys and email when i edit them later
tonight...
"Andy Levy" <andylevy@yahoo.com> wrote in message
news:9o69kp$r7c$1@bent.twistedbits.net...
> I think there's one screw in the front then it pulls down.
>
> Can ya send me a copy of that photo of your switches?
>
> Eric Giblock wrote:
>
> > you can pull down the center console somehow.. i've never done it but
when
> > i
> > got my stereo system installed they did that. they ran about 8 wires to
> > the center console running from where the emergeny brake is up the left
> > side and tuck it in above the head liner from pshing it up from the
front
> > windshield.
> >
> > ttyl
> >
> > --
> > eric giblock
> > student / webdesigner (www.gibsdakota.com)
> > egiblock@hotmail.com
> >
> >
> > ""Kevin (MAGNUM S/T) Hoegen"" <kevinhoegen@email.com> wrote in message
> > news:9o630s$966$1@bent.twistedbits.net...
> >> Hello,
> >> I plan to install my first neon light, and would like to have the
'fused
> >> distribution block' located in the last upper compartment on the
overhead
> >> console (think it is intended for a garage door opener). There is
plenty
> > of
> >> space for the fuse block..and I don't use that compartment for
anything,
> > so
> >> it will allow very easy access to the fuses if needed.
> >>
> >> Additionally I may even put the lighted switch somewhere on this
overhead
> >> console as well....I'm looking at the "clip" location.
> >>
> >> My question: I would like any suggestions on how I can run wires to
this
> >> area. I am slightly hesitant about pulling the roof lining apart as I
> >> have never done this...so I don't know if it will go back the same way.
I
> >> have
> > to
> >> run a wire from the relay (located in the engine compartment) to this
> > dist.
> >> block. I also have to run the sire from the neon light itself
(currently
> >> just a licence plate light.
> >> I could really use some suggestions about WHERE the best places to run
> > wires
> >> are. For the upper console and running wires from the tailgate.
> >>
> >> Note: I am not planning on using pre-exisiting wiring for any of my
> >> connections. All my current and future neons will be on this dedicated
> > fused
> >> circuit. I am just not familiar with the interior body panels and good
> > ways
> >> and locations to run wiring.
> >>
> >> TIA
> >>
> >> --
> >> Kevin Hoegen
> >> 99 Solar Yellow MAGNUM S/T CC
> >> http://webpages.charter.net/khoegen
> >> Flowmaster 3-chamber Dual outlet
> >> Stillen RP w/Dual Hooker Euro tips
> >> Quick-D TB/K&N Intake
> >> 180 RS T-stat/Taylor wires/Autolite plugs
> >> Centerforce II clutch
> >> SpeedTweaks IAT adjuster...etc....etc
> >> (add your link to my site:
> > http://webpages.charter.net/khoegen/links.html )
> >>
> >>
> >>
> >
> >
> >
>
> --
> -andy
> andylevy@yahoo.com
> Maintainer, DML FAQ - http://www.dakota-truck.net/faq/
> http://home.twcny.rr.com/andylevy/dakota/
> '99 CC 4x4 318 auto
This archive was generated by hypermail 2b29 : Fri Jun 20 2003 - 12:02:51 EDT