Sorry for the slow reply. I've been slammed workwise, and out of town this
past weekend.
I'm waiting to order pistons. I have a set of ported Aluminum R/T heads, and
I have a friend with a set of ported iron R/T heads. I'm going to have the
iron ones flowed, and decide which head which will dictate piston dish size.
The iron heads have about a 60cc compared to a 51 cc chamber in the
aluminum. I may be able to buy an off the shelf piston if I go the iron
route. Otherwise I'm looking at 600-700 for a set of custom pistons.
TonyC
-----Original Message-----
From: Sam South <sawcut64@mediaone.net>
To: dakota-truck@buffnet.net <dakota-truck@buffnet.net>
Date: Wednesday, February 06, 2002 7:58 PM
Subject: DML: Re: Attn. TonyC WAS Heres the final blown 318 pics for a
while... got the head off...
>Thanks Tony, I had planned on getting them but I had not done any leg work
>in finding them. So far I just have the block at Koffels Place where I had
>it dipped, and they're still waiting for me to figure out what I'm going to
>do with it....as a matter of fact so am I!! I really don't plan on SCing
it,
>but I would hate to build it and not have that option if I needed :) later.
>I thought the 360 was going to be enough for me but it no longer puts a
>smile on my face...just kind of a grin. How much and where for those
pistons
>you're using and what is the C.R. or available CR's.
>Sam South
>ET 13.61 MPH 105.88
>'95 Dak RC, 5.9L,5-speed,390 LSD
>http://people.mw.mediaone.net/sawcut64/home.html
>http://www.dakota-truck.net/profiles/dakota/Mt5J8FaDfVCv6/profile.htm
>----- Original Message -----
>From: "TonyC" <acellan1@tampabay.rr.com>
>To: <dakota-truck@buffnet.net>
>Sent: Wednesday, February 06, 2002 6:30 PM
>Subject: DML: Re: Re: Re: Re: Re: Re: Heres the final blown 318 pics for a
>while... got the head off...
>
>
>> Sam,
>> If this is a ground up motor, you might want to look into the Milodon 4
>bolt
>> main kit (#11310). I got a set off www.flatlanderracing.com on 237 plus
>> shipping.
>> TonyC
>>
>> -----Original Message-----
>> From: Sam South <sawcut64@mediaone.net>
>> To: dakota-truck@buffnet.net <dakota-truck@buffnet.net>
>> Date: Wednesday, February 06, 2002 11:38 AM
>> Subject: DML: Re: Re: Re: Re: Re: Heres the final blown 318 pics for a
>> while... got the head off...
>>
>>
>> >
>> >Yup, sounds sorta like the 406 I'm working on too, except the crank and
>> >pistons. Anyone have any idea how much boost you can run safely with the
>> >Mopar stroker pistons and crank and a set of I-beam rods?
>> >Sam South
>> >ET 13.61 MPH 105.88
>> >'95 Dak RC, 5.9L,5-speed,390 LSD
>> >http://people.mw.mediaone.net/sawcut64/home.html
>> >http://www.dakota-truck.net/profiles/dakota/Mt5J8FaDfVCv6/profile.htm
>> >----- Original Message -----
>> >From: "TonyC" <acellan1@tampabay.rr.com>
>> >To: <dakota-truck@buffnet.net>
>> >Sent: Wednesday, February 06, 2002 7:37 AM
>> >Subject: DML: Re: Re: Re: Re: Heres the final blown 318 pics for a
>while...
>> >got the head off...
>> >
>> >
>> >> LOW compression Forged pistons, forged crank, good heads, big cam, 4
>bolt
>> >> mains. Oops, sounds like the 408 I'm working on.
>> >> TonyC
>> >>
>> >> -----Original Message-----
>> >> From: Sam South <sawcut64@mediaone.net>
>> >> To: dakota-truck@buffnet.net <dakota-truck@buffnet.net>
>> >> Date: Wednesday, February 06, 2002 6:26 AM
>> >> Subject: DML: Re: Re: Re: Heres the final blown 318 pics for a
while...
>> >got
>> >> the head off...
>> >>
>> >>
>> >> >> Only 6PSI??? what are you thinking... That T-Trim is made for up
to
>> >> >> 26PSI!!! heheheheheh
>> >> >
>> >> >I guess I'm thinking how I'd hate to see that new(and expensive) 406
>> with
>> >a
>> >> >hole in the cylinder!!!
>> >> >Sam South
>> >> >ET 13.61 MPH 105.88
>> >> >'95 Dak RC, 5.9L,5-speed,390 LSD
>> >> >http://people.mw.mediaone.net/sawcut64/home.html
>> >> >http://www.dakota-truck.net/profiles/dakota/Mt5J8FaDfVCv6/profile.htm
>> >> >----- Original Message -----
>> >> >From: "Tim Berry" <coolva1@cox.net>
>> >> >To: <dakota-truck@buffnet.net>
>> >> >Sent: Tuesday, February 05, 2002 10:48 PM
>> >> >Subject: DML: Re: Re: Heres the final blown 318 pics for a while...
>got
>> >the
>> >> >head off...
>> >> >
>> >> >
>> >> >>
>> >> >> Minimum 9PSI for me!! :) I'm B0osT CraZY!!! lol (cant ya tell by
>the
>> >> >> pics?)
>> >> >>
>> >> >> I think if I let her hit 6000 she'da hit 14PSI with the pulley I
had
>> on
>> >> >> it... (2.95" on the V1 T-Trim) I let the computer shift at 5400
>> tho...
>> >> >>
>> >> >> Tim
>> >> >>
>> >> >> > Definitely time for at least a 360, or maybe a 406. Yeah a built
>406
>> >> >with
>> >> >> 6
>> >> >> > PSI of boost....hmmm got me thinking now too!!
>> >> >> > Sam South
>> >> >>
>> >> >> > > http://68.10.88.237:7000/coolva/blown/
>> >> >> > >
>> >> >> > > thats what I've got so far... I just dumped the pics in with
>the
>> >> >older
>> >> >> > ones
>> >> >> > > from yesterday...
>> >> >> > > I think its time for atleast a 360... what bout yall? lol
>> >> >> > >
>> >> >> > > Lemme know what yall think happened... hehehe (Yea, I know its
>> fuct
>> >> >up,
>> >> >> > but
>> >> >> > > what do yall think caused it?)
>> >> >>
>> >> >>
>> >> >
>> >> >
>> >>
>> >
>> >
>>
>
>
This archive was generated by hypermail 2b29 : Fri Jun 20 2003 - 12:03:59 EDT