On a 98 model??? One piece crank pulley started in 2000.
- Bernd
>
> uh gary's stock pulley was a one piece deal. ask him.
>
>
> ----- Original Message -----
> From: "Bernd D. Ratsch" <bernd@texas.net>
> To: <dakota-truck@dakota-truck.net>
> Sent: Wednesday, August 06, 2003 7:15 PM
> Subject: DML: RE: Re: RE: Re: V8 TB and Underdrive install
>
>
> >
> > Nah...no need to remove it. Just jack up the front end and remove the 6
> > bolts holding on the pulley. However, if it's a one-piece pulley (V6's
> > don't use those)....it's a pain in the a$$ without removing the fan and
> > shroud.
> >
> > - Bernd
> >
> > -----Original Message-----
> > From: owner-dakota-truck@bent.twistedbits.net
> > [mailto:owner-dakota-truck@bent.twistedbits.net] On Behalf Of Chad Evans
> > Sent: Wednesday, August 06, 2003 11:39 AM
> > To: dakota-truck@dakota-truck.net
> > Subject: DML: Re: RE: Re: V8 TB and Underdrive install
> >
> >
> >
> > trust me
> > removing the clutch fan will make it easier to do. other wise you have
> > to do
> > it from underneath. the truck.
> > unless the guy has a lift. its best to remove the clutch fan. anyone
> > else out there install one ?
> >
> >
> > ----- Original Message -----
> > From: "Gabriel A. Couriel" <gcouriel@bellsouth.net>
> > To: <dakota-truck@dakota-truck.net>
> > Sent: Wednesday, August 06, 2003 11:40 AM
> > Subject: DML: RE: Re: V8 TB and Underdrive install
> >
> >
> > >
> > > i don't have to remove the clutch fan because i'm only doing the crank
> >
> > > pulley. the only issue i have is running the throttle cable
> > > through... i'm not sure where that goes, and does there have to be an
> > > adjustment made to the cable?
> > >
> > > Gabe Couriel
> > >
> > >
> > > -----Original Message-----
> > > From: owner-dakota-truck@bent.twistedbits.net
> > > [mailto:owner-dakota-truck@bent.twistedbits.net]On Behalf Of Chad
> > > Evans
> > > Sent: Wednesday, August 06, 2003 12:03 PM
> > > To: dakota-truck@dakota-truck.net
> > > Subject: DML: Re: V8 TB and Underdrive install
> > >
> > >
> > >
> > > the TB is a piece of cake. The underdrive pulley is to bad.
> > > I put one on gary's truck. Wasn't bad just had trouble getting the nut
> >
> > > of the clutch fan. that's what 163,000 miles of rust will get you. but
> >
> > > other than that it was pretty easy. 1.8 hrs doesn't seem to long.
> > >
> > >
> > > ----- Original Message -----
> > > From: "Gabriel A. Couriel" <gcouriel@bellsouth.net>
> > > To: "DML" <dakota-truck@dakota-truck.net>
> > > Sent: Wednesday, August 06, 2003 11:05 AM
> > > Subject: DML: V8 TB and Underdrive install
> > >
> > >
> > > >
> > > > about how long does it take to install a V8 TB? also, how long does
> >
> > > > it take to install an underdrive crank pulley? my mechanic wanted
> > > > 1.8 hours to install the two. i don't think it'll take that long to
> >
> > > > do, but how long did
> > > > it take, and how hard was it?
> > > >
> > > > thanks,
> > > >
> > > > Gabriel A. Couriel
> > > >
> > > >
> > >
> > >
> >
> >
>
This archive was generated by hypermail 2b29 : Fri Feb 06 2004 - 11:46:46 EST