stock rear is 3.55
the stock engine is getting close to 70k miles. I will probably getting on it a
lot after its done, so i would prefer a full build. I may also do forced
induction in the future. I really dont trust the stock internals, especially
the racket the engine makes after 4k rpms (it sounds like its gonna come apart)
Bernds V6 was somewhere around 260hp flywheel? or did he get it higher than
that? but he was supercharged, wasnt he?
as for intake manifolds, i found this on hughes website, but theres no talk on
the dml about it.
http://www.hughesengines.com/partDetail.asp?partID=11765&eTypeID=10
can anyone comment on it?
In article <PJEJIAGPKDMHANKKBAEEGEEJCDAA.gcouriel@bellsouth.net>,
gcouriel@bellsouth.net ("Gabriel A. Couriel") writes:
>
>
> probably nowhere near that level. you are gonna be lucky to pull about 220
> from a 3.9L without sacrificing the idle quality. my recommendation would
> be to go with a 206 cam, ported intake manifold, and look at socaldakota's
> ported 3.9L heads, which seem to be a decent deal, considering all the work
> that went into it.
>
> that work can also be done with the 3.9L you have in the truck. not worth
> going all-out on a custom-build lower-end, when you are just going to be
> adding parts that your stock engine can handle. now, if you want to go and
> add a 125-shot of nitrous to that bottom end, you might want to invest in
> some forged pistons and beefier rods, which will require rebuilding the
> engine.
>
> calculate that 250hp is already beyond 1:1 ci:hp. 280 is way beyond that.
> i would stick on the conservative side. 220hp is more than a 5.9L put out
> in stock form, and you have the added benefit of better mileage.
>
> also, what gears are you running? swapping in a set of 4.10's on your truck
> would make a nice difference, especially if going from a stock truck.
>
> Gabriel A. Couriel
>
>
>
> -----Original Message-----
> From: owner-dakota-truck@bent.twistedbits.net
> [mailto:owner-dakota-truck@bent.twistedbits.net]On Behalf Of
> msnbcnnbcbs@hotmail.com
> Sent: Monday, January 15, 2007 12:21 PM
> To: dakota-truck-moderator@bent.twistedbits.net
> Subject: Re: DML: RE: 3.9'er Needs performance advice
>
>
>
> The more i contemplate it, the more prudent it seems to grab a 239 block
> from a
> wrecked dak and go from there. It would save a lot of money, time, and
> hassle.
>
> Anyone know what a 3.9l would max, h.p. wise, without a terrible idle from a
> lopey cam? im guessing 25-280hp naturally aspirated?
>
> i think im definately gonna do it.
>
>
> n article <45AB9769.7080707@aol.com>, SilverEightynine@aol.com (Terrible
> Tom)
> writes:
> >
> >
> > msnbcnnbcbs@hotmail.com wrote:
> > > I thought a 42RE could be set up to handle a 360? it would just need a
> rebuild?
> > >
> > >
> > > In article <PJEJIAGPKDMHANKKBAEEEEEECDAA.gcouriel@bellsouth.net>,
> > > gcouriel@bellsouth.net ("Gabriel A. Couriel") writes:
> > >
> > >>
> > >>if you are going to go the V8 route, keep in mind that you'll need to
> > >>upgrade the transmission. on a 360, you'll have to install a 46RE, and
> all
> > >>the required parts. while you're at it, make sure you install something
> > >>stout, or you might be pulling it to rebuild.
> > >>
> > >>if you are just going to use this to putz around and have fun, you might
> > >>just want to stick to the V6. however, the V8 is tempting.
> > >>
> > >>Gabriel A. Couriel
> >
> > If you go with a 360, you are better off just putting a 46RE into the
> > truck. Keep in mind that the 360 is balanced differently (externally)
> > and you'll need the correct flex plate.
> >
> > If you go with a 360 are you planning on keeping the engine stock or
> > building it up a little? If you are going to build it up, then you may
> > as well get a core engine and rebuild it. If you are keeping it stock,
> > there are a number of places you can get complete engine assemblies,
> > ready to drop in. Only thing else you will need to do is get an engine
> > computer (easy) and the wire harness (NOT easy) Almost all salvage
> > yards do NOT save wire harnesses. I've found you have to get in good
> > with one and ask them to let you know when they get trucks in that you
> > can use parts off, and call you before they butcher them. They cut
> > crossmembers and wire harnesses. All they care about are getting the
> > major componants out (ecm, engine, trans, axles etc)
> >
> > --
> > -------------------------------------------------------------
> > "The word, is no. I am therefore going anyway." - James T. Kirk
> >
> > 75 Honda CL360, 89 Dakota, 89 Dakota 4x4,
> > 95 Dakota 4x4, 96 Neon, 01 Ram 4x4
> > http://members.aol.com/silvereightynine/
> > AIM & Yahoo: SilverEightynine
> >
>
This archive was generated by hypermail 2b29 : Mon Feb 18 2008 - 18:47:20 EST