RE: heater and defrost fan and control

From: Steve Preston (steveophonic@yahoo.com)
Date: Fri Jan 25 2008 - 19:49:49 EST


BTW,it's $11.86. Go to the dealer and buy it,for
sobbing audibly. :)

Thanks!

Steve P.
--- Robert Setree <agm@agm.win.net> wrote:

>
> I unscrewed the resistor bank and it is burnt up.
> The 50 amp fuse did not
> blow. The auto parts store I use said they do not
> have that part and it is
> probably a dealer only part. Do any of you have a
> part number or supplier
> for the resistor bank?
>
> -----Original Message-----
> From: owner-dakota-truck@bent.twistedbits.net
> [mailto:owner-dakota-truck@bent.twistedbits.net] On
> Behalf Of Bernd D.
> Ratsch
> Sent: Tuesday, January 22, 2008 3:14 PM
> To: dakota-truck@dakota-truck.net
> Subject: RE: DML: heater and defrost fan and control
>
>
> They are interchangeable....you don't have the
> factory connector? (But
> yes...you can use properly fitting spade terminals).
>
> - Bernd
>
> -----Original Message-----
> From: Robert Setree [mailto:agm@agm.win.net]
> Sent: Tuesday, January 22, 2008 1:49 PM
> To: dakota-truck@dakota-truck.net
> Subject: RE: DML: heater and defrost fan and control
>
>
> Are they interchangeable if I am willing to put
> spade terminals on the
> existhing wires?
>
> -----Original Message-----g
> From: owner-dakota-truck@bent.twistedbits.net
> [mailto:owner-dakota-truck@bent.twistedbits.net] On
> Behalf Of Bernd D.
> Ratsch
> Sent: Monday, January 21, 2008 6:06 PM
> To: dakota-truck@dakota-truck.net
> Subject: RE: DML: heater and defrost fan and control
>
>
> Yup...the newer (ceramic) ones don't burn up like
> the older resistor boards.
>
>
> - Bernd
>
> -----Original Message-----
> From: Robert Setree [mailto:agm@agm.win.net]
> Sent: Monday, January 21, 2008 11:26 AM
> To: dakota-truck@dakota-truck.net
> Subject: RE: DML: heater and defrost fan and control
>
>
> Good info. My wiring harness had burn up before and
> I have spade terminals
> on my wires plugging into the resistor bank. I can
> get some use from this.
>
> -----Original Message-----
> From: owner-dakota-truck@bent.twistedbits.net
> [mailto:owner-dakota-truck@bent.twistedbits.net] On
> Behalf Of David Gersic
> Sent: Sunday, January 20, 2008 8:16 PM
> To: dakota-truck@dakota-truck.net
> Subject: Re: DML: heater and defrost fan and control
>
>
> On Sunday 20 January 2008 05:54 pm, Robert Setree
> wrote:
> > No speeds work. I have voltages on some
> terminals. I will take it
> > loose and look at the windings.
>
> http://www.zaccaria-pinball.com/temp/im005442.jpg
>
> The black one on the left is the original I pulled
> out. I had only high
> speed working, so there was at least some of the
> resistor wire intact, but
> the other taps were beyond the open.
>
> The green one on the left is the replacement.
>
> http://www.zaccaria-pinball.com/temp/im005443.jpg
>
> The left two terminals are common. The three on the
> right have different
> resistance readings with a meter, leading to four
> total fan speeds.
>
>
>
>
>
>
>
>
>

      ____________________________________________________________________________________
Never miss a thing. Make Yahoo your home page.
http://www.yahoo.com/r/hs



This archive was generated by hypermail 2b29 : Fri Feb 01 2008 - 01:11:51 EST