Since I was the originator of this particular recent thread I'd like to say
thanks for forwarding this on to MSD! I'm going to replace the platinums with
my old splitfires and see what happens. I'll let everyone know.
Thanks again,
Dennis
____________________Reply Separator____________________
Subject: DML: MSD Answers!
Author: bernd@texas.net (Bernd D. Ratsch)
Date: 1/29/99 4:14 PM
Check this out!
> Dear Sir,
>
> We do not recommend using platinum tip plugs with the MSD unit, we also
> recommend gaping the plugs to .050 to .055 to obtain maximum air/fuel
> mixture burn. The platinum plugs have a tendency to run hot and can cause
> detonation. If you have your old plugs or pick up a standard none hype
> plug one step colder and see if that helps. if the plug gets hot enough
> and starts causing some preignition and the computer picks that up it will
> retard the timing which can cause the poor mileage. Reset the computer and
> take the truck out and drive it normally. This will cause the computer to
> relearn with the MSD box in place and help over all. On the O2 Sensor, it
> is only affected when you are under a load condition or full acceleration,
> with light load or cruising it should not add anymore fuel, it is striving
> for 14.7:1 air fuel ratio.
> Thanks,
>
> MSD Tech
>
> ----------
> From: Bernd D. Ratsch[SMTP:]
> Sent: Wednesday, January 27, 1999 6:46 PM
> To: Joe LaPille
> Subject: Question...Problem
> Importance: High
>
> I'm part of a large Dodge Dakota Mailing LIst and we've been seeing
> different scenarios with the MSD 6A boxes. I was wondering if you could
> clear this up for us:
>
> Here's a copy of an email that's going around....
>
> MSD - OBD/II: Pro's & Con's
>
> Original Problem:
> "I just installed a MSD 6A ignition on my '97 Sport 3.9L and my mileage
> went
> from
> ~20 to ~16 mpg's! I thought these things were supposed to increase your
> mileage
> not take it away. Acceleration is much smoother and it seems to have
> improved
> my power but...I have run 2 tanks of gas thru since the install and kept
> my
> foot out of it on
> the second tank thinking it was my driving but the mileage seems the same
> regardless. I also installed Magnecore's and Platinum 4+'s along with the
> ignition but they wouldn't have any thing to do with the mileage
> decrease.Anyone seen the same thing?"
>
>
> Member Answers:
> (1) Are you supposed to run platinum plugs with MSD?
>
> (2) Your spark box/wires/plugs helps to burn the mixture BETTER. so
> there's
> less
> oxygen left for the O2 sensors. Computer thinks less oxygen content in the
> exhaust which means it's too lean and it enriches the mixture by opening
> the
> injectors more. Therefore you're using more gas.
>
> (3) I hope you remembered to gap the plugs at .050. That makes a big
> difference.
>
> (4) Reset the computer
>
> I personally also run the 6470 w/8207 Coil, Splitfire Wires/Plugs (Gapped
> @
> .050") and haven't had anything but great success.
>
> Your help would be greatly appreciated...
>
> On behalf of the Dodge Dakota Mailing List - aka: DML
>
------------------------- Original message header:
>MAIL FROM:<owner-dakota-truck@buffnet4.buffnet.net>
>RCPT TO:<dennis.pendleton@harrisgrp.com>
>DATA
>Received: (from majordom@localhost) by buffnet4.buffnet.net (8.8.7/8.7.3) id RA
A07717 for dakota-truck-outgoing; Fri, 29 Jan 1999 17:18:02 -0500 (EST)
>Received: from buffnet9.buffnet.net (buffnet9.buffnet.net [205.246.19.19]) by b
uffnet4.buffnet.net (8.8.7/8.7.3) with SMTP id RAA07713 for <dakota-truck>; Fri,
29 Jan 1999 17:17:59 -0500 (EST)
>Received: from webserv2.buffnet.net(205.247.125.2) by buffnet9.buffnet.net via
smap (V2.0) id xma018115; Fri, 29 Jan 99 17:13:25 -0500
>Received: from mw4.texas.net (mw4.texas.net [206.127.30.14]) by webserv2.bu
ffnet.net (8.8.7/8.8.7) with ESMTP id RAA17007 for <dakota-truck@buffnet.net
>; Fri, 29 Jan 1999 17:16:56 -0500 (EST) (envelope-from bernd@texas.net)
>Received: from system1 (mnet09-42.austin.texas.net [207.207.50.210]) by mw4.tex
as.net (2.4/2.4) with SMTP id QAA15746 for <dakota-truck@buffnet.net>; Fri
, 29 Jan 1999 16:14:50 -0600 (CST)
>MMDF-Warning: Parse error in original version of preceding line at buffnet9.bu
ffnet.net
>From: "Bernd D. Ratsch" <bernd@texas.net>
>To: Dakota Mailing List <dakota-truck@buffnet.net>
>Subject: DML: MSD Answers!
>Date: Fri, 29 Jan 1999 16:14:40 -0600
>Message-ID:<000301be4bd4$c3ad0a40$020aa8c0@system1.texas.net>
>MIME-Version: 1.0
>Content-Type: text/plain; charset="iso-8859-1"
>Content-Transfer-Encoding: 7bit
>X-Priority: 3 (Normal)
>X-MSMail-Priority: Normal
>X-Mailer: Microsoft Outlook 8.5, Build 4.71.2232.26
>X-MimeOLE: Produced By Microsoft MimeOLE V4.72.3155.0
>Importance: Normal
>Sender: owner-dakota-truck@buffnet4.buffnet.net
>Reply-To: dakota-truck@buffnet.net
>X-Mailing-List: The Dakota Mailing List
>X-Mailing-List-Owner: stei0302@cs.fredonia.edu
>X-URL: http://www.cs.fredonia.edu/~stei0302/WWW/DAKOTA/dakota.html
>X-Unsubscribe-Info: Send "unsubscribe dakota-truck" to majordomo@buffnet.net.
>X-Unsubscribe-URL: http://www.cs.fredonia.edu/~stei0302/WWW/CGI-BIN/dml.html
------------------------- End of message header.
This archive was generated by hypermail 2b29 : Fri Jun 20 2003 - 12:12:19 EDT