Re: Nasty Cam and Stage I heads to ship this Week!

From: Richard A Pyburn (rap777@juno.com)
Date: Tue Jul 13 1999 - 09:27:33 EDT


Andre:

I'm down in San Antonio; I thought that you were in the Dallas vicinity
that's why I said come on down so I can watch ;^).
 I'll bring the book with me to the office tomorrow (7/14) and get 'em
off to you pronto. Don't even think about the phone charges; my pleasure
to help out. Let me know if you need any other pages sent.

Richard Pyburn

On Mon, 12 Jul 1999 20:14:11 -0500 Andre Mauboussin <andrem@ticnet.com>
writes:
>Thanks for the offer Richard. Where are you at? You can fax me at
>(972)
>492-4164. I really would appreciate it. Let me know if its long
>distance so
>I can reimburse you.
>
>Andre
>
>Richard A Pyburn wrote:
>
>> Andre:
>>
>> I've got a '95 FSM but I don't have access to a scanner. Do you
>have a
>> fax number that I can fax these pages to?
>> Better yet, come on down so I can watch! ;^)
>> Richard in SA
>>
>> On Sat, 10 Jul 1999 09:27:35 -0500 Andre Mauboussin
><andrem@ticnet.com>
>> writes:
>> >Hello again everyone;
>> >Sorry I've been so quiet on the list lately. I finally got a
>message
>> >from Dave Hughes of Hughes engines that my stage one ported heads,
>> >custom ground cam and timing set should ship this week(cam has the
>> >following specs .512in .527ex duration 215in 220ex. lobe separation
>> >112deg) The heads have special springs/lock/retainer set-up and are
>> >quite a bit beefier than the MP set. Also, the B&F Stage II
>throttle
>> >body should be here in a matter of days. These parts installed
>along
>> >with some intake mods should spell certain doom for local
>Mudstains,
>> >the
>> >new Lightning, ram-air Batmobiles and unsuspecting corvettes. I've
>> >have
>> >waited long enough, soon the beatings will begin ;-). My
>performance
>> >objective is mid to low 13s. I am in need of the factory service
>> >manual
>> >(I've been told distributor line up can be a pain on the magnum
>> >engine).
>> >I guess I will have to order one unless someone can send me the
>> >section
>> >on cam R&R. I would appreciate any tips any of you may have on the
>> >cam
>> >installation or anything regarding my proposed changes. I'm
>delighted
>> >to
>> >read all the messages about everyone improving the performance of
>> >their
>> >trucks to include all the latest parts and tricks. Best wishes to
>> >all.
>> >
>> >PS Alan, did you make it to the night of fire(I couldn't)?
>> >Andre
>> >
>> >95 Dak Sport Reg cab SB 318 5spd 3:90 Sure Grip
>> >14.5-14.60(Estimated. Truck ran consistent 14.7 before JBA header
>> >install)
>> >
>>
>> ___________________________________________________________________
>> Get the Internet just the way you want it.
>> Free software, free e-mail, and free Internet access for a month!
>> Try Juno Web: http://dl.www.juno.com/dynoget/tagj.
>

___________________________________________________________________
Get the Internet just the way you want it.
Free software, free e-mail, and free Internet access for a month!
Try Juno Web: http://dl.www.juno.com/dynoget/tagj.



This archive was generated by hypermail 2b29 : Fri Jun 20 2003 - 12:14:57 EDT