Re: Mopar muscle article (attn:Mark Pryer)

From: Mark Pryer (mark_pryer@hotmail.com)
Date: Wed Mar 22 2000 - 13:20:49 EST


actually this is for the premag the whole thing was in response to a person
asking what to do to add HP to his 4x4. But are you trying to say it won't
work still? The guy I believe had an 88. If it won't work what can I use?
Mark
91 cc 5spd 6er Dynomax catback 14x3 K&N

----- Original Message -----
From: mike d. <miggitymike@juno.com>
To: <dakota-truck@buffnet.net>
Sent: Tuesday, March 21, 2000 8:37 PM
Subject: Re: DML: Mopar muscle article (attn:Mark Pryer)

> Hey Mark!
>
> keep in mind that these cam figures are safe for a CARBED motor, but your
> TBI motor's computer will not accept any of these cams....
> been there... done that... =(
>
> -mike d.
>
> ---> Yorktown, Va.
> "PROJECT 13's" ... slammed 88 Dakota gettin' a Magnum 360!
>
> miggitymike@juno.com
> http://members.xoom.com/dakotaperf/index.html
>
>
> On Tue, 21 Mar 2000 17:27:03 PST "A. S." <adakota4x4@hotmail.com> writes:
> > Mark:
> > Here's the response--
> > "Your 4x4 Dodge Dakota's drivetrain is more than adequate. Use
> > Mopar's
> > 260/268 degree .430-.450-inch lift cam #P4552810 with their
> > valvesprings
> > #P4120249 and chrome alloy retainers #P4452033. Mopar has a good
> > aluminum
> > four barrel manifold #P4452114, along with a Holley 650 cfm Double
> > Pumper
> > carburetor #0-4777. With the heads, install Mopar's 360 stainless
> > replacement valves 1.88-inch intake #P4876397, 1.60-inch exhaust
> > #P5249187.
> > Then open up the bowls to the bigger valve seats, port match, and do
> > a good
> > three-angle valve job. Mill them at .030-inches to get the
> > compression up.
> > Next, Mopar has headers for your 4x4 Dakota #P4529478. This
> > combination
> > will make 200 horsepower easy. Have fun!"
> >
> > Hope this is what you were looking for!
> > --Aaron--
> > 95 DSRC 4x4 V6
> >
> >
> > >From: "Mark Pryer" <mark_pryer@hotmail.com>
> > >Reply-To: dakota-truck@buffnet.net
> > >To: <dakota-truck@buffnet.net>
> > >Subject: DML: Mopar muscle article needed
> > >Date: Tue, 21 Mar 2000 11:41:44 -0800
> > >
> > >Does anyone still have that Mopar Muscle magazine that had the "Six
> > Appeal"
> > >article in it? If so can I ask a favor. In the back it has reader
> > >questions in it and someone asks about adding hp to a premag. The
> > editor
> > >listed several parts and #s of cams and valve springs and stuff.
> > Can
> > >someone post that response please? It would be much appreciated
> > >Mark
> > >91 cc 5spd 6er Dynomax catback 14x3 K&N
> > >
> >
> > ______________________________________________________
> > Get Your Private, Free Email at http://www.hotmail.com
> >
>
> ________________________________________________________________
> YOU'RE PAYING TOO MUCH FOR THE INTERNET!
> Juno now offers FREE Internet Access!
> Try it today - there's no risk! For your FREE software, visit:
> http://dl.www.juno.com/get/tagj.
>



This archive was generated by hypermail 2b29 : Fri Jun 20 2003 - 11:49:57 EDT