I'm running a 904 in my Shelby as we speak with no problems. All I had to
do is get a bracket for the tranny mount from an 87 V-6 Dakota and shorten
the drive-shaft.
later
Scott
> -----Original Message-----
> From: owner-dakota-truck@buffnet.net
> [mailto:owner-dakota-truck@buffnet.net]On Behalf Of Shari & Marty
> Sent: Tuesday, April 11, 2000 12:37 AM
> To: dakota-truck@buffnet.net
> Subject: DML: Re: Re: DC Transmission for a 426 Hemi Motor-Question
>
>
> I know of 904's fitting, what information do you have that does
> not support
> this?
> Kuk
> ----- Original Message -----
> From: "Bernd D. Ratsch" <bernd@texas.net>
> To: <dakota-truck@buffnet.net>
> Sent: Monday, April 10, 2000 9:13 PM
> Subject: DML: Re: DC Transmission for a 426 Hemi Motor-Question
>
>
> > Here's a little tid-bit of info:
> >
> > If you can find one, grab a "Hemi TorqueFlite" (they're VERY
> rare) but it
> > will bolt right up. It came with an extra wide kickdown band and a 5th
> > clutch (unlike the regular torqueflite).
> >
> > A regular 727 (from let's say a 440) will work just fine with a
> heavy duty
> > clutch pack and make sure that all the clearances are correct
> (accurate to
> > boot). Art Carr may make a special drum and clutch pack but that might
> get
> > a little bit expensive. A 904 will NOT fit no matter what others say.
> >
> > - Bernd
> >
> >
> > -----Original Message-----
> > From: owner-dakota-truck@buffnet.net
> > To: dakota-truck@buffnet.net
> > Subject: DML: Re: RE: Re: DC Transmission for a 426 Hemi Motor-Question
> >
> >
> > > Could this one handle a 700HP flux? If not what mods are required to
> make
> > > it handle around 600-700HP range?
> > >
> > > ----------------------------------
> > > Steven St.Laurent
> > >
> > > -----Original Message-----
> > > From: Bernd D. Ratsch [mailto:bernd@texas.net]
> > > Subject: DML: Re: DC Transmission for a 426 Hemi Motor-Question
> > >
> > > Old reliable of course: 727
> > >
> > >
> > > ----- Original Message -----
> > > From: "Stlaurent Mr Steven" <STLAURENTS@mctssa.usmc.mil>
> > > Subject: DML: DC Transmission for a 426 Hemi Motor-Question
> > >
> > >
> > > > For 426 Hemi crate motor, what current DC transmission application
> > would
> > > I
> > > > get the best performance and blow proof?
> > > >
> > > > ----------------------------------
> > > > Steven St.Laurent
> > > > Test Engineer
> > > > Test Branch, GSD, MCTSSA
> > > > MARCORSYSCOM, USMC
> > > > Tel: (760) 725-2296
> > > > stlaurents@mctssa.usmc.mil
> > > > mailto:Saint1958@home.com
> > > >
> > > >
> > > >
> > >
> >
> >
> >
>
> _____________________________________________
> NetZero - Defenders of the Free World
> Click here for FREE Internet Access and Email
> http://www.netzero.net/download/index.html
>
This archive was generated by hypermail 2b29 : Fri Jun 20 2003 - 11:50:41 EDT