I guess that's my motivation to get this PCM emulator up and running.;-)
Shawn
-----Original Message-----
From: owner-dakota-truck@BUFFNET.NET
[mailto:owner-dakota-truck@BUFFNET.NET]On Behalf Of Bernd D. Ratsch
Sent: Friday, June 22, 2001 5:41 PM
To: dakota-truck@buffnet.net
Subject: DML: RE: Superchargers on, WhooooHoooo Q&A
(1) You want to be rich at WOT (To a point...no real way to tell without
putting it on a wide-band O2 "sniffer" to check the A/F correctly)
(2) YES...Sh-tcan that POS filter that comes with the Powerdyne...only
flows about 400-500CFM max. (You'll need at least 750-800CFM)
(3) If you're already running that rich, it won't help out...you'll need
to get the A/F issue first before fine tuning it with the IAT Adjuster.
Why isn't it shifting properly? (Go back to your factory PCM program
for a bit and you'll see...you know what I mean on that one Shawn.)
- Bernd
-----Original Message-----
From: owner-dakota-truck@buffnet.net
[mailto:owner-dakota-truck@buffnet.net] On Behalf Of Shawn Bowen
Sent: Friday, June 22, 2001 1:45 PM
To: dakota-truck@buffnet.net
Subject: DML: Superchargers on, WhooooHoooo Q&A
Well, went to a friends house expecting to just hang out. We installed
my PowerDyne while hanging out!!! We skipped the FMU and Fuel pump for
now as I have 24# injectors and an A/F meter that I can keep an I on.
I'm running the stock 6 Pounder, MAN what a difference. The A/F is
STILL RICH at WOT!!! Maybe you folks can guide me here with a few minor
issues:
1) Originally I had sent my PCM to Leach for a blower flash, it's been
running rich as shit waiting on the blower. Now, WITHOUT the Extra Fuel
Pump and FMU I am STILL rich at WOT!!! Go figure. This is with the 6#
pulley, I would expect to lean out a little with the 9#er I'm going to
put on after break in. My biggest headache is that after the flash and
before the SC at WOT I would stop at 4600-4700RPMS. When I say stop,
it's not a rev limiter, rather I didn't think their was enough air to
blow the fuel. So now, SC on at WOT I BLAST past 4600RPM's to 5300ish
and then it WILL NOT SHIFT until I slightly let off the throttle,
WTF???? When I do let off slightly BAM I'm through the RPM's in a flash
and have to back off again slightly to shift again. Any Ideas??? I'm
thinking that the shift points are slightly higher and the 6#er isn't
feeding enough air to pound through them. HMMMMM. Suggestions
welcome!!!
2) Next, I haven't installed a boost gauge yet, and I'm running the
factory PowerDyne Air filter in the fender well. That puppy is WAY
undersized for this kind of air movement. I plan on moving back to my
old 6x9 K&N as soon as I find a reasonable place to put it, Any
suggestions here??? I thought about the same place as the cold air
setup, however this beast chews up a lot of real estate as it is, I'm
concerned that if I put the K&N there the belt on the SC will rub.
3) I have an IAT adjuster but it does not seem to help any. I can not
get it to lean out at WOT, I need dyno time to get everything right, but
I'm waiting on gauges, K&N filter placement, 9# pulley, and what not
first.
Why oh why will my damn truck not shift on it's own??? Not enough air
to blow through???
Next steps are the original 6x9 K&N filter is going back on, and I'm
also installing a test blow by valve for Bernd (not installed yet but it
will be, thanks buddy). I may play with the FMU and new fuel pump but
at the moment, unless the group speaks otherwise, I'm running rich at
WOT, why put even MORE fuel into it??? I've got to tighten down the
header y-pipes, AGAIN. I also HAVE to get my gauges in, I have the A/F
hooked up and running but it's rapped around my 4WD lever;-)... Here's
the mods so far just for any folks perusing looking to provide input:
98 5.2L 4x4 CC Auto
52mm Flow Metric's TB
Cold Air Intake
DynoMax dual Catback
JBA Ceramic Headers
PowerDyne @ 6PSI (Everything but FMU and Fuel pump done!!!)
Custom Pop off (Air release) for the Supercharger (Here but needs
to
be installed and documented)
Custom PCM Blower Flash
24# SVO matched Injectors
1.7 Crower RR's
Mopar Valve Covers
Mopar Chromoly Pushrods
Mopar Heavy Duty Springs/Retainers
Autolite 3923's (soon to be 3922's)
MSD6BTM (On the back burner, still deciding)
MSD SS Coil (Here but not installed yet)
MSD 8.5mm Wires
Electric Fan (Ditched the Clutch Fan)
Bernd's IAT Adjuster
4.10 Front/Rear Diff's (Ordered)
Auburn Suregrip (Ordered)
Thanks for any and all help/advice!!!!
Shawn
I got Blown tonight;-)
This archive was generated by hypermail 2b29 : Fri Jun 20 2003 - 12:01:51 EDT