Hey Larry, I'm down at Mark house getting his butt up so we can finish
swapping in my 360, and it downloads fine from here, but we both have he
same cable provider. This isn't the first time I've been told about this,
but I'm not sure what to do about it, I've tried downloading it to the
server again and other then that I'm not sure what to do. By the way I ran
that day a 14.15 @ 97.81.
Sam South
sawcut64@mediaone.net
http://people.mw.mediaone.net/sawcut64/home.html
----- Original Message -----
From: "Larry" <Larrysemail@larry.com>
To: <dakota-truck-moderator@bent.twistedbits.net>
Sent: Sunday, July 15, 2001 7:19 AM
Subject: DML: Re: Re: Re: Attn: John S and Sam South, was:
cam/rockers/intake/tb/injectors are in
> Hey Sam,
>
> I visited your website and downloaded the 1/4 mile run of yours, but it
cuts
> off right before I can see your time/speed. I tired a couple of times but
> still dont work. I even tried save as, but it still didnt show the end.
Is
> it just me or is it messed up?
>
>
> ""Sam South"" <sawcut64@mediaone.net> wrote in message
> news:000b01c10cdb$46d638a0$4c0a1e18@mw.mediaone.net...
> > OK Skippy, just remember I work on your truck just as much(if not more)
as
> > you do on mine!!!!
> > Sam South
> > 95 Dak, 5.2L,3.90 LSD,5-speed(Soon to be 360 powered)
> > 14.10@98.05
> > http://www.twistedbits.net/WWWProfile/dakota/Mt5J8FaDfVCv6/
> > http://people.mw.mediaone.net/sawcut64/home.html
> >
> > ----- Original Message -----
> > From: "Mark Kuzia" <flyboy01@mediaone.net>
> > To: <dakota-truck@buffnet.net>
> > Sent: Saturday, July 14, 2001 10:43 PM
> > Subject: DML: Re: Attn: John S and Sam South, was:
> > cam/rockers/intake/tb/injectors are in
> >
> >
> > > > Anyhow I'd like to thank everyone ahead of time for all there input
> > (Jon,
> > > >Bernd, Mark, and many others). I am thanking you now because if I
> screwed
> > > up
> > > > somewhere and the engine doesn't run right I'll probably be cursing
> you
> > > all
> > > > for getting me back into the hot rodding scene.
> > > > So wish me luck, I'll let you know what happens on monday.
> > >
> > > Attn: John S and Sam South
> > >
> > > My standard disclaimer.........
> > >
> > > There are no guarantees or warranties neither expressed nor implied.
Any
> > > information and help I have provided is to be taken at your own risk.
As
> > an
> > > adult it is your responsibility to verify and research and all
> information
> > > shared and make sure all work performed is to your standards. It is
also
> > > your responsibility entirely if you screw anything up that I may have
> > > recommended, provided incorrect information on, or that I have
performed
> > > labor on in a faulty manner. All speed equipment MUST be installed and
> > > operated by qualified experts and technicians only. My liability is
> hereby
> > > limited by the terms and conditions set forth in this document. This
> > > disclaimer applies to all situations except the following:
> > >
> > > 1) Everything you have done by my advice turns out as expected, in
that
> > > case, I accept all public praise and admiration everyday for at least
a
> > > period of one week, and henceforth at least once a week for a period
of
> 90
> > > days.
> > >
> > > 2) If in fact the performance meets/exceeds your expectations, you may
> > send
> > > monetary gifts directly to my home address in the form of cash,
> certified
> > > checks, and money orders. These gifts may also be disbursed in person,
> but
> > I
> > > do advise against it as I may grow tired of you quickly. Monetary
gifts
> > must
> > > exceed $100, and must be disbursed on the same schedule as described
in
> > the
> > > previous paragraph.
> > >
> > > Thank You,
> > > Mark Kuzia
> > > flyboy01@mediaone.net
> > > http://people.mw.mediaone.net/flyboy01/home.html
> > > 1995 Dakota 13.79 @ 102.45 mph
> > > ~360ci, 5-spd, 4.11 LS (8 3/4 [3.90 SG] coming soon)
> > > 1994 Dakota 15.36 @ 91.56 mph
> > > ~318ci, 5-spd, 3.90 LS (bone stock, no mods)
> > >
> > >
> > > ----- Original Message -----
> > > From: <Pukeloser@aol.com>
> > > To: <dakota-truck@buffnet.net>
> > > Sent: Saturday, July 14, 2001 1:58 AM
> > > Subject: DML: cam/rockers/intake/tb/injectors are in
> > >
> > >
> > > > Ok fellas,
> > > >
> > > > I have installed the cam (Hughes 1814), lifters, valve springs, 1.6
> > > roller
> > > > rockers, ported intake manifold, hughes stage 2 TB, FMS 24#
injectors,
> > > > progear DR timing chain and K&N X-stream filter. I am not starting
the
> > > engine
> > > > 'til monday so I can have someone else there to keep an eye on
> > everything
> > > > while I do the ole cam break-in thing.
> > > > I am sorta nervous and way excited to see if I didn't screw up.
> > > > Anyhow I'd like to thank everyone ahead of time for all there input
> > (Jon,
> > > > Bernd, Mark, and many others). I am thanking you now because if I
> > screwed
> > > up
> > > > somewhere and the engine doesn't run right I'll probably be cursing
> you
> > > all
> > > > for getting me back into the hot rodding scene.
> > > > So wish me luck, I'll let you know what happens on monday.
> > > >
> > > > PS There is a chance that I'l be able to do it today (sat) but I'm
> not
> > > sure
> > > > yet.
> > > >
> > > > Thanks
> > > >
> > > > John S
> > >
> >
>
>
This archive was generated by hypermail 2b29 : Fri Jun 20 2003 - 12:02:06 EDT