RE: How to unsubscribe

From: Ronald Wong (ron-wong@cox.net)
Date: Wed Jun 26 2002 - 20:26:01 EDT


BAHAHAHA

Ron
00 PB SLT QC 4X2 5.9 46RE 3.92 LSD
For modifications see my DML Profile (URL follows)
http://www.twistedbits.net/WWWProfile/dakota/Kw9pV1EkFeOYY

-----Original Message-----
From: owner-dakota-truck@dakota-truck.net
[mailto:owner-dakota-truck@dakota-truck.net]On Behalf Of
joel.esler@us.army.mil
Sent: Wednesday, June 26, 2002 1:37 PM
To: dakota-truck@dakota-truck.net
Subject: DML: How to unsubscribe

How to unsubscribe

     First, ask your Internet Provider to mail you an Unsubscribing
     Kit. Then follow these directions. The kit will most likely be
     the standard no-fault type. Depending on requirements, System
     A and/or System B can be used. When operating System A,
     depress lever and a plastic dalkron unsubscriber will be
     dispensed through the slot immediately underneath. When you
     have fastened the adhesive lip, attach connection marked by
     the large "X" outlet hose. Twist the silver- coloured ring one
     inch below the connection point until you feel it lock.

     The kit is now ready for use. The Cin-Eliminator is activated
     by the small switch on the lip. When securing, twist the ring
     back to its initial condition, so that the two orange lines
     meet. Disconnect.

     Place the dalkron unsubscriber in the vacuum receptacle to the
     rear. Activate by pressing the blue button.

     The controls for System B are located on the opposite side.
     The red release switch places the Cin-Eliminator into
     position; it can be adjusted manually up or down by pressing
     the blue manual release button. The opening is self-
     adjusting. To secure after use, press the green button, which
     simultaneously activates the evaporator and returns the Cin-
     Eliminator to its storage position.

     You may log off if the green exit light is on over the
     evaporator. If the red light is illuminated, one of the Cin-
     Eliminator requirements has not been properly implemented.
     Press the "List Guy" call button on the right of the
     evaporator. He will secure all facilities from his control
     panel.

     To use the Auto-Unsub, first undress and place all your
     clothes in the clothes rack. Put on the velcro slippers
     located in the cabinet immediately below. Enter the shower,
     taking the entire kit with you. On the control panel to your
     upper right upon entering you will see a "Shower seal" button.
     Press to activate. A green light will then be illuminated
     immediately below. On the intensity knob, select the desired
     setting. Now depress the Auto-Unsub activation lever. Bathe
     normally.

     The Auto-Unsub will automatically go off after three minutes
     unless you activate the "Manual off" override switch by
     flipping it up. When you are ready to leave, press the blue
     "Shower seal" release button. The door will open and you may
     leave. Please remove the velcro slippers and place them in
     their container.

     If you prefer the ultrasonic log-off mode, press the indicated
     blue button. When the twin panels open, pull forward by rings
     A & B. The knob to the left, just below the blue light, has
     three settings, low, medium or high. For normal use, the
     medium setting is suggested.

     After these settings have been made, you can activate the
     device by switching to the "ON" position the clearly marked
     red switch. If during the unsubscribing operation you wish to
     change the settings, place the "manual off" override switch in
     the "OFF" position. You may now make the change and repeat the
     cycle. When the green exit light goes on, you may log off and
     have lunch. Please close the door behind you.

Joel Esler
Network Security Analyst



This archive was generated by hypermail 2b29 : Fri Jun 20 2003 - 12:04:51 EDT