I know for a fact Mopar Performance does not make a V6 Cam. I asked Koller
Dodge today when I ordered my gaskets, timing chain, & springs.
Not to get off topic, but wouldnt you want to replace the valves while your
in there?
Gary Hedlin
"The Crazy Quadraplegic"
ghedlin@theramp.net (business)
ragingquad@yahoo.com (personal)
**Also Webmaster For**
http://garyhedlin.com
http://socaldakota.com
http://scsilverdak.com
http://assistivetechnologies.com
...And Many More!
""Gabriel A. Couriel"" <BigGabe@FIUFIJI.com> wrote in message
news:LGEHJPEPBFBBEPPBEOFMCEFMCAAA.BigGabe@FIUFIJI.com...
>
> and they make them for V6? i thought that the cams sold by MP were V8
only.
>
> Gabe Couriel
> http://frontpage.tripod.com/fijigabe0
>
> -----Original Message-----
> From: owner-dakota-truck@bent.twistedbits.net
> [mailto:owner-dakota-truck@bent.twistedbits.net]On Behalf Of Wes Weems
> Sent: Thursday, September 19, 2002 6:46 PM
> To: dakota-truck@dakota-truck.net
> Subject: Re: DML: A few cam questions... need advice!
>
>
>
> you can get a mopar performance mild perf cam, for lowend power, and its
> actually cheaper than a regular replacement, but the dealer said chrysler
> doesnt have them in stock and it would be weeks before they could get one.
>
> Wes
> ----- Original Message -----
> From: "Gabriel A. Couriel" <BigGabe@FIUFIJI.com>
> To: <dakota-truck@dakota-truck.net>
> Sent: Thursday, September 19, 2002 3:13 PM
> Subject: RE: DML: A few cam questions... need advice!
>
>
> >
> > i think he also asked about performance cams for the V6, i'm interested
on
> > this subject, so are there any cams to help out the V6 on mildly
modified
> > engines?
> >
> > Gabe Couriel
> > http://frontpage.tripod.com/fijigabe0
> >
> > -----Original Message-----
> > From: owner-dakota-truck@bent.twistedbits.net
> > [mailto:owner-dakota-truck@bent.twistedbits.net]On Behalf Of
> > jon@dakota-truck.net
> > Sent: Thursday, September 19, 2002 5:32 PM
> > To: dakota-truck-moderator@bent.twistedbits.net
> > Subject: Re: DML: A few cam questions... need advice!
> >
> >
> >
> > "Wes Weems" <wweems@fix.net> wrote:
> >
> > : will I need new bearings lifters etc? My FSM shows how to pull the
> lifters
> > : and clean em, and they work for now... I am just so damn broke I cant
> > afford
> > : anythign. =(
> >
> > No, you shouldn't need to change the bearings and lifters unless they
> > are damaged. (Normally you would replace the lifters on a flat tappet
> > cam, but since the Magnums use a roller cam, they can be re-used). As
> > far as the bearings go, if they are bad, the engine would probably need
> > to be pulled to replace them anyway, so hope that they are good. :-)
> > (They should be OK though.)
> >
> >
> > --
> >
> > -Jon-
> >
> > .---- Jon Steiger ------ jon@dakota-truck.net or
> jon@jonsteiger.com -----.
> > | I'm the: AOPA, DoD, EAA, NMA, NRA, SPA, USUA. Rec & UL Pilot - SEL
> |
> > | '70 Barracuda, '92 Ram 4x4, '96 Dakota, '96 Intruder 1400, '96
FireFly
> |
> > `-----------------------------------------
> http://www.jonsteiger.com ----'
> >
>
>
This archive was generated by hypermail 2b29 : Fri Jun 20 2003 - 12:05:22 EDT