contact chris hogan from the list. he has put one on also. he might be able
to give some insight as well.
----- Original Message -----
From: "Gabriel A. Couriel" <gcouriel@bellsouth.net>
To: <dakota-truck@dakota-truck.net>
Sent: Wednesday, August 06, 2003 12:20 PM
Subject: DML: RE: Re: RE: Re: V8 TB and Underdrive install
>
> i was planning on going from underneath anyways... the only way i'm
> removing
> that fan is when it's permantently gone (replaced with the Viper fan). i
> was going to get it installed today, but i had to get 2 new rotors and a
> new
> passenger caliper because it was sticking, and i was told it had gone bad.
>
> this stuff keeps adding up.
>
> Gabe Couriel
>
>
> -----Original Message-----
> From: owner-dakota-truck@bent.twistedbits.net
> [mailto:owner-dakota-truck@bent.twistedbits.net]On Behalf Of Chad Evans
> Sent: Wednesday, August 06, 2003 12:39 PM
> To: dakota-truck@dakota-truck.net
> Subject: DML: Re: RE: Re: V8 TB and Underdrive install
>
>
>
> trust me
> removing the clutch fan will make it easier to do. other wise you have to
> do
> it from underneath. the truck.
> unless the guy has a lift. its best to remove the clutch fan.
> anyone else out there install one ?
>
>
> ----- Original Message -----
> From: "Gabriel A. Couriel" <gcouriel@bellsouth.net>
> To: <dakota-truck@dakota-truck.net>
> Sent: Wednesday, August 06, 2003 11:40 AM
> Subject: DML: RE: Re: V8 TB and Underdrive install
>
>
> >
> > i don't have to remove the clutch fan because i'm only doing the crank
> > pulley. the only issue i have is running the throttle cable through...
> > i'm
> > not sure where that goes, and does there have to be an adjustment made
> > to
> > the cable?
> >
> > Gabe Couriel
> >
> >
> > -----Original Message-----
> > From: owner-dakota-truck@bent.twistedbits.net
> > [mailto:owner-dakota-truck@bent.twistedbits.net]On Behalf Of Chad Evans
> > Sent: Wednesday, August 06, 2003 12:03 PM
> > To: dakota-truck@dakota-truck.net
> > Subject: DML: Re: V8 TB and Underdrive install
> >
> >
> >
> > the TB is a piece of cake. The underdrive pulley is to bad.
> > I put one on gary's truck. Wasn't bad just had trouble getting the nut
> > of
> > the clutch fan. that's what 163,000 miles of rust will get you. but
> > other
> > than that it was pretty easy. 1.8 hrs doesn't seem to long.
> >
> >
> > ----- Original Message -----
> > From: "Gabriel A. Couriel" <gcouriel@bellsouth.net>
> > To: "DML" <dakota-truck@dakota-truck.net>
> > Sent: Wednesday, August 06, 2003 11:05 AM
> > Subject: DML: V8 TB and Underdrive install
> >
> >
> > >
> > > about how long does it take to install a V8 TB? also, how long does
> > > it
> > > take
> > > to install an underdrive crank pulley? my mechanic wanted 1.8 hours
> > > to
> > > install the two. i don't think it'll take that long to do, but how
> > > long
> > > did
> > > it take, and how hard was it?
> > >
> > > thanks,
> > >
> > > Gabriel A. Couriel
> > >
> > >
> >
> >
>
>
This archive was generated by hypermail 2b29 : Fri Feb 06 2004 - 11:46:45 EST