The squair part on the end of an easy out isn't for VICE GRIPS!!!
They will pull crooked and maybe make matters worse. It is made to fit in a
TAP HANDLE some of which will accept a 3/8 drive ratchet. On the high end
they do make a set of sockets that fit the shanks of the taps and easy outs.
GEORGE!!
----- Original Message -----
From: "Mark Kuzia" <flyboy01@mediaone.net>
To: <dakota-truck@BUFFNET.NET>
Sent: Sunday, May 27, 2001 10:20 AM
Subject: DML: Re: changing thermostat, bolt snaps inside hole!!!
> Just in case I didn't make it clear last night, an EZ-out looks like a
very
> coarse tapered left handed drill bit with a square shank on one end so you
> can get a pair of vicegrips on it. All the suggestions are very good,
> however, I would FIRST try the EZ-out, as you may not be able to use it
once
> you try the other methods. If that fails then try drilling out the bolt
with
> a reverse drill, then if that fails, drill it out completely and Heli-coil
> it (if you want to keep the same size bolt). Let us know how it goes.
>
> Mark Kuzia
> flyboy01@mediaone.net
> http://people.mw.mediaone.net/flyboy01/home.html
> 1995 Dakota 13.79 @ 102.45 mph
> ~360ci, 5-spd, 4.11 LS (8 3/4 [3.90 SG] coming soon)
> 1994 Dakota 15.36 @ 91.56 mph
> ~318ci, 5-spd, 3.90 LS (bone stock, no mods)
>
>
> ----- Original Message -----
> From: "Michael Stepka" <genesisd@mediaone.net>
> To: <dakota-truck@BUFFNET.NET>
> Sent: Sunday, May 27, 2001 8:54 AM
> Subject: DML: RE: Re: changing thermostat, bolt snaps inside hole!!!
>
>
> > Thank you everyone who gave me some suggestions. I am going to go ride
> my
> > bike to the hardware (in the rain!) to get a left hand drill bit. Also
I
> > will probably get some EZ out. Thanks so much for all the help. I am
> > going to take my time and try my best. Wish me luck! I will let you
> > know how I made out when I am done! Thanks.
> >
> > Mike
> >
> >
> > -----Original Message-----
> > From: owner-dakota-truck@BUFFNET.NET
> > [mailto:owner-dakota-truck@BUFFNET.NET]On Behalf Of Josh Hancock
> > Sent: Sunday, May 27, 2001 7:17 AM
> > To: dakota-truck@BUFFNET.NET
> > Subject: DML: Re: changing thermostat, bolt snaps inside hole!!!
> >
> >
> > Mike the same thing happened to me just two weeks ago.
> > so I know how you feel! ;-( I tried the reverse drill bit ,
> > easy out and a few others but ended up drilling it out
> > and retapping one size bigger.
> > I hope you can get it out!
> >
> > Josh
> >
> >
> > ----- Original Message -----
> > From: "Michael Stepka" <genesisd@mediaone.net>
> > To: <dakota-truck@BUFFNET.NET>
> > Sent: Saturday, May 26, 2001 10:27 PM
> > Subject: DML: changing thermostat, bolt snaps inside hole!!!
> >
> >
> > > I was changing my thermostat today and the bolt snapped inside the
hole.
> > I
> > > don't know what to do. I can't use the truck till I fix it. Any
> > > suggestions, do you think if I drill the bolt out I can retap it?
> > >
> > > thanks.
> > >
> > >
> > > Mike
> > > genesisd@mediaone.net
> > >
> > >
> >
>
>
This archive was generated by hypermail 2b29 : Fri Jun 20 2003 - 12:01:34 EDT