Hey, it works on the Dak...it works on the PC. luck of the draw...as they
say.
Ron
00 PB SLT QC 4X2 5.9 46RE 3.92 LSD
For modifications see my DML Profile (URL follows)
http://www.twistedbits.net/WWWProfile/dakota/Kw9pV1EkFeOYY
-----Original Message-----
From: owner-dakota-truck@buffnet.net
[mailto:owner-dakota-truck@buffnet.net]On Behalf Of Bernd D. Ratsch
Sent: Saturday, June 16, 2001 6:10 PM
To: dakota-truck@buffnet.net
Subject: DML: RE: RE: Re: AAAARRRGGGGHH!
"Plug and Pray"
-----Original Message-----
From: owner-dakota-truck@buffnet.net
[mailto:owner-dakota-truck@buffnet.net] On Behalf Of Ronald Wong
Sent: Saturday, June 16, 2001 8:05 PM
To: dakota-truck@buffnet.net
Subject: DML: RE: Re: AAAARRRGGGGHH!
Okay, it seems to have resolved itself. Once I went through the BIOS
setup I guess it figured out what it needed to do. I now have three
partitions of 10 GB each. Now for Partition Magic, then Windows on one
of them, then wait for XP to get here, load my Dak scanner stuff in the
third one (Dak content), and voila, I'm done.
Ron
00 PB SLT QC 4X2 5.9 46RE 3.92 LSD
For modifications see my DML Profile (URL follows)
http://www.twistedbits.net/WWWProfile/dakota/Kw9pV1EkFeOYY
-----Original Message-----
From: owner-dakota-truck@buffnet.net
[mailto:owner-dakota-truck@buffnet.net]On Behalf Of Bill Pruitt
Sent: Saturday, June 16, 2001 5:12 PM
To: dakota-truck@buffnet.net
Subject: DML: Re: AAAARRRGGGGHH!
Are you installing this hard drive through a PCI add-in card or direct
IDE to the motherboard? If direct to the motherboard, it should not have
and effect on your Network card. If you are using a PCI interface card,
try moving it to another open PCI slot as far away from the network card
as possible.
Bill Pruitt
'01 QC 4.7, Auto, Flo-Pro exhaust, Downey Tarp, Viper Alarm, RhinoLiner,
K&N Glas-Scapes "Stars and Stripes", "Tail-Gate Open" warning light
http://web.tampabay.rr.com/billspages/
----- Original Message -----
From: "Ronald Wong" <ron-wong@home.com>
To: <dakota-truck@buffnet.net>
Sent: Saturday, June 16, 2001 7:50 PM
Subject: DML: AAAARRRGGGGHH!
> Okay, PC buffs. I am trying to install a new Maxtor Diamondmax VL 30
> GB hard drive in an old PC of mine. This old PC is a P-II 333 mhz.
> Motherboard has the 440 LX chipset on it.
>
> When I boot up I get the following error:
>
> ERROR-Resource Conflict PCI Network Controller
> Bus: 00, Device: 10,
> Function: 00
>
> Why?
>
> Thanks,
>
> Ron
> 00 PB SLT QC 4X2 5.9 46RE 3.92 LSD
> For modifications see my DML Profile (URL follows)
> http://www.twistedbits.net/WWWProfile/dakota/Kw9pV1EkFeOYY
>
This archive was generated by hypermail 2b29 : Fri Jun 20 2003 - 12:01:49 EDT