what no price... ;)
come on just say "very roughly $$$"
Tim Althoff
99 RC Dak w/ V6 5-speed
http://go.to/yllwdkta
-----Original Message-----
From: owner-dakota-truck@BUFFNET.NET
[mailto:owner-dakota-truck@BUFFNET.NET]On Behalf Of Bernd D. Ratsch
Sent: Wednesday, January 23, 2002 5:15 PM
To: dakota-truck@BUFFNET.NET
Subject: DML: RE: RE: Hyper Speed Controller - Working and noticeably
better already
Actually, it's for just about any vehicle with an O2 sensor (or two).
It monitors the O2 signal (we'll use A/F for ease of understanding) and
corrects it to 14.7:1 under normal cruise and 12.0:1 under WOT (WOT is
adjustable +/-1.0).
Again, the final product will be ready in 90 days (this is the one with
the USB port).
- Bernd
-----Original Message-----
From: owner-dakota-truck@BUFFNET.NET
[mailto:owner-dakota-truck@BUFFNET.NET] On Behalf Of Tim Althoff
Sent: Wednesday, January 23, 2002 10:01 PM
To: dakota-truck@BUFFNET.NET
Subject: DML: RE: Hyper Speed Controller - Working and noticeably better
already
ok bernd...I need to take out a little stress (I am supposed to have my
Computer science program done by Friday at 5pm and have almost
nothing...I NEED TO BUY SOME NEW TOYS!!!
is this for highly modded or could I get some results from my lightly
modded 3.9. (cold air, TB, ignition, exhaust, 180*, modified intake,
locker...soon to be 3.90 gears, elec fan, pulley. How do you adjust it?
I know laptop but how adjustable is it?
most importantly what cost going to look like? thanks
Tim Althoff
99 RC Dak w/ V6 5-speed
http://go.to/yllwdkta
-----Original Message-----
From: owner-dakota-truck@BUFFNET.NET
[mailto:owner-dakota-truck@BUFFNET.NET]On Behalf Of Bernd D. Ratsch
Sent: Wednesday, January 23, 2002 4:26 PM
To: Dakotart@yahoogroups.com
Subject: DML: HyperSpeed Controller - Working and noticeably better
already
Yup...the HyperSpeed Controller (Proto-Type Rev-II) is installed and
functioning as claimed. Much better throttle response, no overly rich
(or lean) smell from the tailpipe (home-brew A/F meter...aka: nose), and
the kicker is the lean spot caused by the supercharger at 1-2# boost
under 1/2-3/4 throttle...it's not there anymore.
It took about 50 miles for the PCM to relearn the new (corrected)
settings from the HyperSpeed controller (reset the PCM after the initial
installation) and adjusted the high-end enrichment a little bit (will
need to put back to normal in about 50 more miles or so).
The final box will be released in 90 days with a USB port, completely
sealed box (for under the hood installation), and software for your
laptop. This will allow the end user to fine-tune the fuel curve
(across the RPM band in small increment as well)...this means
programmable and automatic. Yes..you can adjust on the fly (while
driving).
I put some pictures of the Proto-Type installation on the SpeedTweaks
website (Engine Controls/HyperSpeed) but keep in mind that the final
controller will be Plug and Play with your factory O2 sensor(s).
Yes...it replaces your stock (forward) O2 sensor(s). With all this
said, it's also 100% SMOG LEGAL (CARB EO#).
I'll be heading to the Dyno shop this Friday to get some HP and TQ
readings, but the butt-dyno already noticed the change...nothing else
was installed in the mean time.
- Bernd
This archive was generated by hypermail 2b29 : Fri Jun 20 2003 - 12:03:50 EDT